3D Printing Filament Weight Calculator

  • PLA (1.24 g/cm³)
  • ABS (1.04 g/cm³)
  • PETG (1.27 g/cm³)
  • TPU (1.21 g/cm³)
  • Nylon (1.14 g/cm³)
  • Resin (1.1 g/cm³)
  • 1.75 mm
  • 2.85 mm
Results
—
—

Planning a 3D printing project and wondering how much material you'll need? Our Filament Weight Calculator estimates the exact weight, length, and cost of filament required for your prints, helping you plan spool purchases and budget accurately.

The calculator works with all common 3D printing materials — PLA, ABS, PETG, TPU, Nylon, and resin. Each material has a different density, and the tool automatically applies the correct conversion factor. Enter your print volume in cubic centimeters (found in your slicer software), select your material, and choose your filament diameter.

Weight is calculated simply as volume × density. Length calculation accounts for the filament's cylindrical shape — thinner 1.75mm filament stretches further per gram than 2.85mm filament. Most slicer software will give you a weight estimate directly, so you can use that as input here.

Cost estimates help you compare materials — premium filaments like carbon fiber reinforced nylon cost more per gram than basic PLA, but may require less material for equivalent strength. Always add a 10-20% buffer to account for purge lines, brims, and failed print attempts.

3D Printer Filament: Weight, Length, and How a 1 kg Spool Works

The Two Formulas

Filament is a long cylinder, so its weight comes from volume × density:

volume = π × (d/2)2 × length   →   weight = volume × density

For the common 1.75 mm diameter and PLA's density of about 1.24 g/cm³, a 1 kg spool holds roughly 278 meters of filament (1000 ÷ 1.24 = 806 cm³; ÷ 0.024 cm³ per cm of filament ≈ 33,600 cm). The same spool of PETG (1.27) is a little shorter, ABS (1.04) noticeably longer - about 333 m - which is exactly why slicers that estimate by length disagree with your scale by 10-20% when you switch material.

Why Spools Are Sold by Weight but Measured by Length

Your printer's extruder pushes length (the slicer commands "extrude 5,000 mm"), but filament is bought and shipped by weight. Converting between them requires knowing both the diameter and the density - and diameter itself comes in two standards, 1.75 mm and 2.85 mm, whose weights differ by the square of the ratio: about 2.65× per unit length. A 1 kg spool of 2.85 mm filament is less than 40% of the length of a 1 kg spool of 1.75 mm. Feed the wrong one and every print estimate collapses.

Estimating a Print Before You Start

The practical workflow: run the slicer's material estimate (grams or meters), then check stock by weighing the spool on a kitchen scale - weight remaining − spool tare = grams available. If you only know the length left on the spool, convert it back through the formulas above. This calculator does the whole circle: enter any two of diameter, length, density, and it returns the rest.

Cost per Print Is a Two-Step Division

Filament cost per gram = spool price ÷ 1000. A $22 kg of PLA is 2.2¢/g, so the 86 g bracket from the slicer costs $1.89 of plastic - before printer time, electricity, and failed first layers. Comparing two filament prices per spool instead of per gram is how a "cheap" 750 g spool ends up more expensive than a 1 kg one.

Multi-Material Caution

Densities to keep straight: PLA 1.24, PETG 1.27, ABS 1.04, TPU ~1.21, nylon 1.09 g/cm³. If you swap materials often, the weight-per-meter of your stock changes enough that "half a spool left" means different lengths in each material - weigh, don't eyeball, and the calculator turns the grams into meters whenever you need the other half of the answer.

Formula
Weight = Volume × Density ; Length = Weight ÷ (π × (Diameter/2)² × Density)

FAQ

How do I find print volume in cm³?
Your slicer software (Cura, PrusaSlicer, Simplify3D) typically shows estimated filament usage in grams and meters. Multiply gram weight by material density or check the g-code preview for volume estimates. Alternatively: Volume = Layer Height × Print Area.
How much filament is in a typical spool?
Most standard spools contain 1 kg of filament. For PLA, that's approximately 100-120 meters of 1.75mm filament. Specialty filaments like carbon fiber or infused materials often come in 500g spools.
Should I add a buffer to my filament estimate?
Yes — we recommend adding 10-15% extra to account for purge lines, failed prints, and material left on the nozzle. For complex prints with many supports, add 20-25% extra.
Is resin 3D printing cheaper than FDM?
Resin material costs about 3-5 times more per gram than standard FDM filament. However, resin prints require less material for solid, detailed parts. Compare costs using volume-based pricing, not just per-gram rates.

Embed this calculator on your site

Cite this page

About these results

Every calculation on this page runs locally in your browser using published, standard formulas — nothing you enter is sent to a server. Results are estimates for planning purposes and can differ from real-world conditions; always follow your local building code and the advice of a qualified professional for final decisions. You can read more about who builds and maintains these tools on our About page. About MateCalc.